- How much does a yard of concrete cover 4 inches thick?
- Can I pour a 2 inch concrete slab?
- How many bags of concrete do I need for a 10×20 slab?
- Should you put plastic under concrete?
- What is the minimum depth for concrete?
- Can I pour concrete directly on dirt?
- Can I pour a 3 inch concrete slab?
- Is it cheaper to mix your own concrete?
- Do you need rebar for 4 inch slab?
- Do you need gravel under concrete?
- How strong is 2 inches of concrete?
- How thick does a concrete slab need to be for a shop?
- What is the best base for a concrete slab?
- How long does it take for 4 inches of concrete to cure?
How much does a yard of concrete cover 4 inches thick?
One Cubic Yard of Concrete: 4-inches thick – covers 81 square feet.
5-inches thick – covers 65 square feet..
Can I pour a 2 inch concrete slab?
If done properly, new concrete can often be poured right over an existing slab. For this to be feasible, the contractor needs to pour at least 2 inches thick, use smaller aggregate, and incorporate reinforcement such as welded wire mesh or fiber mixed into the concrete.
How many bags of concrete do I need for a 10×20 slab?
A 60-pound bag yields . 017 cubic yards, and an 80-pound bag yields . 022 cubic yards. For a 10 x 10 slab, you would need 77 60-pound bags or 60 80-pound bags.
Should you put plastic under concrete?
A concrete vapor barrier is any material that prevents moisture from entering a concrete slab. Vapor barriers are used because while fresh concrete is poured wet, it’s not supposed to stay that way. It needs to dry and then stay dry to avoid flooring problems. … This is why a vapor barrier under concrete is essential.
What is the minimum depth for concrete?
125mmMinimum Thickness Of Concrete Slabs Eurocode 2 states minimum thickness for floor slabs in buildings is 125mm.
Can I pour concrete directly on dirt?
Long story short, yes you can pour concrete over dirt.
Can I pour a 3 inch concrete slab?
Here, pouring a concrete slab 4 inches in thickness is fine. While you may choose to reinforce it with rebar, wire mesh should be sufficient. … A 3- to 4-inch slab will work for the floor of a storage or tool shed, workshop, garden shed, or playhouse.
Is it cheaper to mix your own concrete?
One of the least expensive ways to get concrete is to mix your own. You can buy bags of the mix from a home improvement store. Typically, you only have to add water for it to be ready to pour. … Otherwise, you risk getting a weaker concrete once it cures, which could lead to cracks or crumbles within a couple of years.
Do you need rebar for 4 inch slab?
No, you do not need rebar for a 4-inch slab of concrete on grade. A 4-inch-thick slab cast on the ground and in permanent contact with it will float and rebar is not required. Rebar is recommended on concrete measuring 5 – 6 inches thick.
Do you need gravel under concrete?
Whether you pour concrete for a walkway or patio, a strong gravel base is required to prevent the concrete from cracking and shifting. Gravel is especially important in clay soil because it doesn’t drain well, which results in water pooling under the concrete slab and slowly eroding the soil as it finally drains.
How strong is 2 inches of concrete?
How strong is 2 inches of concrete? A common bag of concrete, for example, may have a compression strength of 4,000 psi, based on a thickness of 2 inches after it has set for 28 days. Other concrete may have a compression strength of only 550 psi.
How thick does a concrete slab need to be for a shop?
Five to six inchesFive to six inches is recommended if the concrete will receive occasional heavy loads, such as motor homes or garbage trucks. To prepare the base, cut the ground level to the proper depth to allow for the slab thickness.
What is the best base for a concrete slab?
Most concrete contractors want a mix of coarse and fine aggregate to create a compactable base that is going to be safe for settlement and drainage. Crusher run (a mix of crushed stone and stone dust) is one of the best base materials for concrete flatwork.
How long does it take for 4 inches of concrete to cure?
When waiting for concrete to dry, keep these timeframes in mind: 24 to 48 hours – after inital set, forms can be removed and people can walk on the surface. 7 days – after partial curing, traffic from vehicles and equipment is okay. 28 days – at this point, the concrete should be fully cured.