- How difficult is it to relocate a toilet?
- Can toilet drain go straight down?
- What happens if a toilet is not vented?
- Can a toilet shower and sink share a vent?
- How much space do you need between toilet and shower?
- Is it expensive to relocate a toilet?
- Can I move my toilet away from the wall?
- How close can a toilet be to the wall?
- What is wrong with the toilet?
- What is the smallest size for a bathroom?
- Why does my toilet randomly run for a few seconds?
- Can you switch a toilet and shower?
- Are all toilets the same distance from the wall?
- Can you move a toilet location?
- How far can you move a toilet from the stack?
- Can toilets touch walls?
- What is the toilet stack?
- Why is the water in the toilet moving?
How difficult is it to relocate a toilet?
If you are remodeling a second floor bathroom, moving the toilet will likely require demolition of first floor ceilings and walls so you can move the water lines inside the structure of the house.
Yes, this can also become messy, difficult, and costly.
But, it can be done..
Can toilet drain go straight down?
Toilet drains do go straight down to the lateral, where a slope allows the waste to flow to the sewer or septic tank. … The trap prevents the sewer gas from backing up in the room, and this system works for both wall mounted and floor mounted fixtures.
What happens if a toilet is not vented?
Poorly-vented drain lines will not be able to effectively move wastewater and solid waste out of your building. This could lead to problems such as overflowing drains, backed-up toilets, and similar plumbing issues.
Can a toilet shower and sink share a vent?
(Sinks, tubs, showers all have 1.5 fixtures units each). As a general rule, you will just be able to vent 2 fixtures on a toilet wet vent. … The toilet drain should be 3″, the sink drain is 1.5″, the shared sink drain/toilet vent area should be 2″, and the vent going up should be 1.5″.
How much space do you need between toilet and shower?
The distance from the centerline of a toilet and/or bidet to any bath fixture, wall, or other obstacle should be at least 18 inches. Code Requirement: A minimum distance of 15 inches is required from the centerline of a toilet and/or bidet to any bath fixture, wall, or other obstacle.
Is it expensive to relocate a toilet?
The cost to move a toilet or sinks can be $2,500-$3,500 per fixture. Plumbing can be a significant cost factor in a remodel when a bathroom floor plan is altered. The toilet is the most expensive to move.
Can I move my toilet away from the wall?
Moving the toilet is not a change to be taken lightly. But if needed, it can be accomplished with substantial plumbing work and a great deal of peripheral work, such as opening up a floor or ceiling, rerouting pipes and drain flange, and re-installing the toilet and other fixtures.
How close can a toilet be to the wall?
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.
What is wrong with the toilet?
One cause of a toilet running is a flapper that doesn’t seal. … Flush the toilet and look for a fill valve leak. Lift up on the toilet float arm when the tank is filling to see if the water stops. Bend or adjust the toilet float arm so the tank stops filling when the water level is 1/2- to 1-in.
What is the smallest size for a bathroom?
15 square feetBelow are common bathroom size layouts. In general, the smallest size is 15 square feet, which can fit a sink and a toilet. For a shower, to be installed, at least 30-36 square feet is required. For a full bath consisting of both a shower and a bathtub, you will need at least 40 square feet.
Why does my toilet randomly run for a few seconds?
A toilet that cuts on and off by itself, or runs intermittently, has a problem that plumbers call a phantom flush. The cause is a very slow leak from the tank into the bowl. … The solution is to drain the tank and bowl, check and clean the flapper seat, and replace the flapper if it’s worn or damaged.
Can you switch a toilet and shower?
Can you put a toilet where a shower was? The simple answer is yes, you can put a toilet where a shower was, but the move doesn’t come without its issues. This isn’t a simple DIY job. You are going to have to remove at least one wall and, hopefully, only a small portion of the floor.
Are all toilets the same distance from the wall?
Keep in mind you need some space on the sides as well. Toilet Rough In Dimensions: A toilet’s rough-in measurement is the space between the wall behind the toilet and the center of the waste pipe. Standard toilet rough in dimensions are 12 inches but can be anywhere from 10 to 14 inches in some cases.
Can you move a toilet location?
Moving a toilet is not a straightforward weekend DIY job, but it is very doable when you involve the professionals. Once the toilet itself is removed, your plumber will have to move the drainage, as well as the water supply to accommodate the new location.
How far can you move a toilet from the stack?
6-feetIn short, your toilet must be no more than 6-feet away from the stack if the waste line diameter is 3-inches. If the waste line diameter is 4-inches, the toilet must be no more than 10-feet away from the stack. Read on to find out more about the distance between the toilet and stack and moving your toilet.
Can toilets touch walls?
When installing a toilet, there is not a specific distance that the toilet tank should be from the wall. Whether your toilet is one inch from the wall or touching the wall directly, it is really up to your preference.
What is the toilet stack?
The main stack is a vent pipe that runs through the center of your home and exits through the roof. The stack connects to the home’s soil stack and branches off into the every room that uses plumbing pipes. The stack is also a part of the house’s drainage system.
Why is the water in the toilet moving?
When the wind blows over the vent stack outlet on the roof, the air pressure in the pipe is lowered. … The lowered pressure in the pipes creates a slight suction effect throughout the plumbing system, pulling on water in the toilet below.